Synced from Product Parameters V2: Basic & Appearance
| | PLA-Aero PRO effect of printing temperature on foaming |
|---|---|
| Recommended printing conditions | Nozzle Temperature230-270°COptimum Foaming temperature260 ℃ Recommended Nozzle h ≥ 0,4 mmRecommended build surface treatmentGlass, vuchi Film or PC FilmBuild plate temperature50°CChamber TempN/ACooling fan speedOpenPrint speed30-90 mm/sRetraction distanceoffRetraction speedoffRecommended Support MaterialN/ADrying setting50-55℃ for 4-5hAnnealingN/A |
| | Nozzle Temperature230-270°COptimum foaming temperature260 ℃Recommended Nozzle H ≥ 0,4 mmRecommended build surface treatmentGlass, vuchi Film or PC FilmBuild piastra temperature50 ° CChamber TempN/ACooling fan speedOpenPrint speed30-90 mm/sRetraction distanceoffRetraction speedoffRecommended Support MaterialN/ADrying setting50-55 ℃ for - 5hAnnealingN 4 / A/td > < / tr > < / tbody > < / tavola > < > h3 stampa Tips < / > h3 < p > stampa Tips: Since PLA-Aero Pro adopts the “On-Demand foaming” technology, the filament will continue to expand in the nozzle after being heated during the printing process. Therefore, it will cause unavoidable stringing during the nozzle movement. Even adjusting the retraction setting in the slicing software cannot solve this problem. Based on the above, it is recommended to turn off the retraction setting. The string on the surface of models can easily be removed by hand.
PRODUCT PARAMETERS V2
Parametri di stampaValori sincronizzati dal profilo prodotto V2 collegato — punto di partenza per slicing e prove di stampa. Printing WindowCore temperature, speed and cooling settings from Product Parameters V2.
Nozzle Temperature
210 - 250 °C
Bed Temperature
50 - 50 °C
Print Speed
40 - 100 mm/s
Cooling Fan
100 - 100 %
Hardware & PlatformNozzle, build plate and pre-print preparation recommendations.
Build Plate Material
玻璃、PEI膜、PC膜或涂抹PVP固体胶
Support & CompatibilitySupport material, spacing and compatible material recommendations.
Raft Gap
0.2 - 0.2 mm
Application cases for this filament
Live listings from the Application Cases section (same taxonomy as the CMS).
1 cases
No FAQs for this product yet. 通用安全提示（FusRock）
耗材（防潮）储存要求
耗材受潮处理方案及方法
烘干参数 PTC 小型烘干盒：60–70℃，烘干 4–6 小时。 小型恒温鼓风烘干机：箱内温度场往往不均匀，可能导致料盘变形；此类设备上建议适当降低温度并缩短单次烘干时间（示例：40–45℃，约 4 小时），并结合材料详情中的干燥建议综合判断。 重要：若按此温度烘干后打印效果仍无改善，请先用空料盘做温度测试，再酌情提高烘干温度，以防温度过高或不均匀导致料盘烘干变形。 大型恒温鼓风烘干机：60–70℃，烘干 4–6 小时。 PS：为什么不同烘干设备适用温度会有差别？可在后台插入说明或外链「点击了解」。 注意事项 ⚠ 操作前请阅读
（可插入「变形 vs 正常」料盘对比照片，注意控制烘干温度与摆放方式。） 干燥受潮对比 耗材受潮的影响
（可插入 RH80% 环境下拆封后第 1 / 2 / 3 天打印同一模型的对比图。） * 上述吸湿对比示例可能因产品系列而异（例如 PAHT-CF），请在插入图片时于脚注中注明材料系列。 No application disclaimer to display yet. Link a Product Parameters V2 record to this product in the admin. Copyright & Terms of Use Notice
Thank you for visiting our website! Please carefully read the following Copyright Statement and Terms of Use before using this website: Copyright Statement All content on this website, including but not limited to texts, images, graphics, audios, videos, software, as well as their compilations, codes and technical architectures (collectively referred to as the "Content"), are owned by this website or relevant right holders and protected by the Copyright Law of the People's Republic of China and other applicable laws and regulations. Without the prior written authorization of this website, no entity or individual may copy, repost, disseminate, modify, display, adapt, mirror, upload, download or otherwise use the Content of this website in any form. The copyright of any third-party content quoted on this website shall belong to the original right holders. If your legitimate rights and interests are infringed due to reasons not attributable to this website, please contact us promptly, and we will handle the matter immediately upon verification. Terms of Use You may browse, download or print the Content of this website for non-commercial purposes in compliance with relevant laws, regulations and this Notice, provided that all copyright notices and other proprietary information are retained without any modification whatsoever. Any commercial use of the Content or services of this website is strictly prohibited, including but not limited to creating derivative works based on the Content, selling or distributing the Content to third parties. It is prohibited to use automated tools (such as crawlers, robots, etc.) to obtain, copy, monitor or attempt to access the content or data of this website. Disclaimer This website endeavors to provide accurate and reliable information, but makes no express or implied warranties regarding the completeness, timeliness or accuracy of the Content. This website shall not be held legally liable for any direct or indirect losses arising from your use of the Content or services of this website. This website may contain links to third-party websites, and this website assumes no responsibility for the content and acts of any third-party websites. Rights Protection If you violate this Notice and infringe upon the legitimate rights and interests of this website, we reserve the right to pursue legal liabilities, including but not limited to filing a lawsuit or taking other legal measures. Should you have any inquiries regarding this Notice, please contact us via: [email protected] The final right of interpretation of this Notice belongs exclusively to this website.  
|
|---|
