Synced from Product Parameters V2: Basic & Appearance
| | ASA-Aero LT effect of printing temperature on foaming |
|---|---|
| Recommended printing conditions | Nozzle Temperature240-280°CRecommended Nozzle h ≥ 0,4 mmRecommended build surface treatmentGlass, vuchi Film or PC FilmBuild piastra temperature80-110 ° CChamber TempSealing or 40-70°CCooling fan speed0-50%Print speed30-90 mm/sRetraction distanceoffRetraction speedoffRecommended Support MaterialN/ADrying setting60℃ for 4-5hAnnealingN/A |
Printing Tips: 1.Since ASA-Aero adops the ‘on-demand foaming’ technology, the filament will continue to expand in the nozzle after being heated during the printing process. Therefore, it will cause unavoidable stringing during the nozzle movement. Even adjusting the retraction setting in the slicing software cannot solve this problem. Based on the above, it is recommended to turn off the retraction setting.2.Because ASA materials have a high glass transition temperature, A certain anidride temperature (40-70 ° C) is richiesto dispersoldi stampa istruzione of the printed interno individual the parts and reduce warping. When printing thin-walled models without any form of insulation, L’impiego di un metodo con il diametri di 0,6 mm o più per ridurre l’esposizione alle sostanze chimiche shrinkage.3.When printing with ASA-Aero filaments, please place the enclosed printer in a ventilated environment.
No matching print profile files.
Valori sincronizzati dal profilo prodotto V2 collegato — punto di partenza per slicing e prove di stampa.
Core temperature, speed and cooling settings from Product Parameters V2.
Nozzle, build plate and pre-print preparation recommendations.
Support material, spacing and compatible material recommendations.
No FAQs for this product yet.
通用安全提示（FusRock）
| 短期不使用时 | 放入密封防潮盒或进行简易抽真空即可，避免阳光直射。 |
|---|---|
| 长期不使用 | 将耗材放入出厂铝箔袋并尽量排出袋内空气（条件允许时在袋内再放一包干燥干燥剂）；外套一层家用抽真空保鲜袋后抽真空。置于阴凉干燥处，避免阳光直射。 |
PTC 小型烘干盒：60–70℃，烘干 4–6 小时。
小型恒温鼓风烘干机：箱内温度场往往不均匀，可能导致料盘变形；此类设备上建议适当降低温度并缩短单次烘干时间（示例：40–45℃，约 4 小时），并结合材料详情中的干燥建议综合判断。
重要：若按此温度烘干后打印效果仍无改善，请先用空料盘做温度测试，再酌情提高烘干温度，以防温度过高或不均匀导致料盘烘干变形。
大型恒温鼓风烘干机：60–70℃，烘干 4–6 小时。
PS：为什么不同烘干设备适用温度会有差别？可在后台插入说明或外链「点击了解」。
⚠ 操作前请阅读
（可插入「变形 vs 正常」料盘对比照片，注意控制烘干温度与摆放方式。）
耗材受潮的影响
| 未受潮 | 受潮 |
|---|---|
| 表面相对整洁、颜色正常、力学性能在规格内 | 可能出现痘痕/毛刺/拉丝、颜色发白、力学性能下降等（因材料而异） |
（可插入 RH80% 环境下拆封后第 1 / 2 / 3 天打印同一模型的对比图。）
* 上述吸湿对比示例可能因产品系列而异（例如 PAHT-CF），请在插入图片时于脚注中注明材料系列。
No application disclaimer to display yet. Link a Product Parameters V2 record to this product in the admin.
