同步自产品参数管理V2:基础与外观信息
| PropertyTesting methodTypical valueDensityISO 11831.19 g/cm³HardnessISO 761990AMelt index200°C,2.16kg22 g/10minVicat softening temperatureISO 30695°CTensile breaking strength (X-Y)ISO 52728.12±3.26 MPaelongation at break (X-Y)520±51 %tensile stress at 100% (X-Y)8.55±0.32 MPatensile stress at 200% (X-Y)10.26±0.14 MPatensile stress at 300% (X-Y)14.38±0.55 MPaSpecimens printed under the following conditions: Nozzle size 0.4mm,Nozzle temp 210°C, Bed temp 50°C, Print speed 60mm/s, Infill 100%, Infill angle ±45° | Recommended printing conditions |
|---|---|
| Additional Suggestions:1.If you want to achieve high-speed printing, it is recommended to use direct extruders, such as BMG extruder, Titan extruder and Hemera extruder, and appropriately increase the nozzle temperature.2.TPU material is very easy to absorb moisture when exposed to air, and printing after absorbing moisture will result ozzing, extruding with bubbles and rough surface appearance, thus reducing print quality.It is recommended that put the filament into a dry box (humidity below 15%) immediately after opening the FusFlex™ FusFlex™ TPU90A-HF vacuum foil bag for printing.Please put the unused filament back into the original aluminum foil bag for sealed storage.3.After the material is damp, there will be more printing ozzing, bubbles extruded and rough printing surface.Please dry the filament in an oven at 70-80℃ for 4-6h to restore the printing quality of FusFlex™ FusFlex™ TPU90A-HF. | FAQ |
| Most frequent questions and answers | Size specifications of 1KG consumables? |
| Disclaimer | Fusrock® 3D printing filaments are suitable for general printing applications and have been tested under standard conditions.However, the performance and safety of printed products are influenced by multiple factors, including printing parameters, model design, operating environment, and intended use.By using Fusrock® materials, users acknowledge and agree to independently evaluate the suitability of printed items for their specific applications and assume all associated risks.Fusrock® shall not be held liable for any damages, injuries, or losses resulting from the practical use of products printed with its materials, including but not limited to structural failures, malfunctions, or safety hazards in operational environments.Thorough testing must be conducted before applying printed components to critical, functional, or commercial scenarios.Fusrock® products are not certified for medical, aerospace, or life-support systems, except for certifications explicitly stated by Fusrock® for specific materials. |
| Related Articles | All |
| Additional Suggestions:1. | |
|---|---|
| Related Articles | All |
| FusFlex™ TPU90A-HF | A 3D printed unicycle sports brace based on TPU90A |
| Manufacturing and R&D | Others | FusFlex™ TPU90A-HF | FUSE REALROCK FUTURE |
暂无匹配的打印配置文件。
以下参数同步自关联的产品参数管理V2,可作为切片与试打调参的起点。
同步自产品参数管理V2的温度、速度与冷却建议。
喷嘴、底板以及打印前准备建议。
支撑材料、支撑间距和兼容耗材建议。
暂无收录的解决方案条目,敬请期待。
暂无收录的常见问题,敬请期待。
通用安全提示(FusRock)
| 短期不使用時 | 放入密封防潮盒或進行簡易抽真空即可,避免陽光直射。 |
|---|---|
| 長期不使用 | 將耗材放入出廠鋁箔袋並盡量排出袋內空氣(條件允許時在袋內再放一包幹燥幹燥劑);外套一層家用抽真空保鮮袋後抽真空。置於陰涼幹燥處,避免陽光直射。 |
PTC 小型烘幹盒:60–70℃,烘幹 4–6 小時。
小型恒溫鼓風烘幹機:箱內溫度場往往不均勻,可能導致料盤變形;此類設備上建議適當降低溫度並縮短單次烘幹時間(示例:40–45℃,約 4 小時),並結合材料詳情中的幹燥建議綜合判斷。
重要:若按此溫度烘幹後打印效果仍無改善,請先用空料盤做溫度測試,再酌情提高烘幹溫度,以防溫度過高或不均勻導致料盤烘幹變形。
大型恒溫鼓風烘幹機:60–70℃,烘幹 4–6 小時。
PS:為什麼不同烘幹設備適用溫度會有差別?可在後臺插入說明或外鏈「點擊了解」。
⚠ 操作前請閱讀
(可插入「變形 vs 正常」料盤對比照片,注意控制烘幹溫度與擺放方式。)
耗材受潮的影響
| 未受潮 | 受潮 |
|---|---|
| 表面相對整潔、顏色正常、力學性能在規格內 | 可能出現痘痕/毛刺/拉絲、顏色發白、力學性能下降等(因材料而異) |
(可插入 RH80% 環境下拆封後第 1 / 2 / 3 天打印同一模型的對比圖。)
* 上述吸濕對比示例可能因產品系列而異(例如 FusForce™ FusForce™ PAHT-CF),請在插入圖片時於腳注中注明材料系列。