Products

FusForce Series

FusForce™ FusForce™ PET-GF

PET-GF

FusForce™PET-GF是專門爲FDM 3D打印工藝開發的。基材採用PET工程材料,具有吸溼性低、強度高、抗蠕變、耐溶劑、耐熱性高等特點。在印刷過程中,它具有優異的尺寸穩定性,沒有上升或下降的邊緣,不收縮,沒有氣味,不需要環境絕緣。也可與FusFree™S-Multi易剝離支撐材料結合使用,解決複雜模型中支撐面成型效果差的問題。
未退火73.9 退火后99.1
HDT-A 热变形温度 / degC
未退火77.4 退火后120.3
HDT-B 热变形温度 / degC
未退火4011.36 退火后4130.13
拉伸模量 / Young 模量(多状态) / MPa
未退火64.65 退火后70.86
拉伸强度(多状态) / MPa
线径1.75mm 重量2.5kg / 3kg
线盘规格(线径/重量)
  • 规格参数
  • 配置下载
  • 打印参数
  • 相关下载
  • 应用案例
  • 常见问题
  • 健康小提示
  • 受潮处理和储存
  • 应用免责声明
  • 声明和版权
加載材料的功能特性(與雷達對比的物性表)…< / div > < / div >
PRODUCT PARAMETERS V2

FusForce™ PET-GF

同步自产品参数管理V2:基础与外观信息

产品名称 FusForce™ PET-GF
产品型号 PET-GF
适配成型方式 FDM设备使用耗材
颜色与外观 纯色(Natural)、红色(Red)、橙色(Orange)、蓝色(Blue)、灰色(Grey)、黑色(Black)
重量规格 2.5 kg / 3 kg
线径规格 1.75 mm
品牌 FusRock
供应商 FusRock

Material Properties

Recommended printing conditions ​Nozzle Temperature280–320 °CRecommended Nozzle Diameter0.4-1.0 mmRecommended build surface treatmentPEI or Coating with PVP glueBuild plate temperature60-80 °CChamber TempSupports printing without sealingCooling fan speedOffPrint speed30-120 mm/sRetraction distance1-3 mmRetraction speed1800-3600 mm/minRecommended Support MaterialFusFree™ S-Multi Quick-Remove SupportDrying setting100-120℃ for 4-6hAnnealing80-100℃ for 4-8h 

Recommended printing conditions

Nozzle Temperature280–320 °CRecommended Nozzle Diameter0.4-1.0 mmRecommended build surface treatmentPEI or Coating with PVP glueBuild plate temperature60-80 °CChamber TempSupports printing without sealingCooling fan speedOffPrint speed30-120 mm/sRetraction distance1-3 mmRetraction speed1800-3600 mm/minRecommended Support MaterialFusFree™ S-Multi Quick-Remove SupportDrying setting100-120℃ for 4-6hAnnealing80-100℃ for 4-8h 

Printing Tips

Printing Tips:1.Although the moisture absorption of PET material is very low, it is very sensitive to moisture. Printing after absorbing moisture will result in ozzing, extruding with bubbles and rough surface appearance, thus reducing print quality. It is recommended that put the filament into a dry box (humidity below 15%) immediately after opening the FusForce™️ FusForce™ PET-GF vacuum foil bag for printing. Please put the unused filament back into the original aluminum foil bag for sealed storage.  2.After the material is damp, there will be more printing ozzing, bubbles extruded and rough printing surface. Please dry the filament in an oven at 100-120℃ for 4-6h to restore the printing quality of FusForceTM FusForce™ PET-GF.  3.Phaetus hardened steel and above grade nozzles shall be selected, which can effectively improve the print quality. Besides, it is recommended that the thickness of the heating block should no less than 12mm.  After the printing, the printed part can be annealed to further improve the strength of FusForceTM FusForce™ PET-GF print part. Annealing conditions: place the printed part at 80-100℃ for 4-8 hours and cool to room temperature naturally.

  • 资料类型
  • 版本号
  • 时间
  • 操作
  • TDS
  • 5.1
  • 2025-02-01
  • 暂无匹配的打印配置文件。

    PRODUCT PARAMETERS V2

    打印参数

    以下参数同步自关联的产品参数管理V2,可作为切片与试打调参的起点。

    打印窗口

    同步自产品参数管理V2的温度、速度与冷却建议。

    喷嘴温度 280 - 320 °C
    底板温度 80 - 100 °C
    打印速度 30 - 120 mm/s
    建议喷嘴直径 0.4 - 1 mm

    硬件与平台

    喷嘴、底板以及打印前准备建议。

    建议底板材质 PEI底板或者涂抹PVP固体胶

    支撑与兼容

    支撑材料、支撑间距和兼容耗材建议。

    Raft 间距 0.08 - 0.12 mm
    回抽距离 0.4 - 1 mm
    回抽速度 30 - 60 mm/s

    暂无收录的解决方案条目,敬请期待。

    暂无收录的常见问题,敬请期待。

    通用安全提示(FusRock)

    1. 长期大量使用 3D 打印材料时,建议在专用房间操作并保持通风。
    2. 有过敏史者请确认所用材质不会引发过敏反应。
    3. 有呼吸道慢性病者请佩戴口罩;其他人员也强烈建议操作时佩戴口罩。
    4. 对纤维类打印件进行打磨、切割等可能产生纤维逸出的操作时,请做好防护,避免刺入或吸入。
    5. 打印时请远离儿童与婴幼儿,注意环境安全。

    耗材(防潮)储存要求

    短期不使用时 放入密封防潮盒或进行简易抽真空即可,避免阳光直射。
    长期不使用 将耗材放入出厂铝箔袋并尽量排出袋内空气(条件允许时在袋内再放一包干燥干燥剂);外套一层家用抽真空保鲜袋后抽真空。置于阴凉干燥处,避免阳光直射。
    耗材受潮处理方案及方法
    烘干参数

    PTC 小型烘干盒:60–70℃,烘干 4–6 小时。

    小型恒温鼓风烘干机:箱内温度场往往不均匀,可能导致料盘变形;此类设备上建议适当降低温度并缩短单次烘干时间(示例:40–45℃,约 4 小时),并结合材料详情中的干燥建议综合判断。

    重要:若按此温度烘干后打印效果仍无改善,请先用空料盘做温度测试,再酌情提高烘干温度,以防温度过高或不均匀导致料盘烘干变形。

    大型恒温鼓风烘干机:60–70℃,烘干 4–6 小时。

    PS:为什么不同烘干设备适用温度会有差别?可在后台插入说明或外链「点击了解」。

    注意事项

    操作前请阅读

    1. 没有把握的请先用空料盘进行温度测试,以防温度过高或不均匀导致料盘烘干变形。
    2. 请严格遵循材料详情页 / 材料参数管理中推荐的烘干温度与时间。
    3. 建议使用鼓风干燥箱;不要让出风口直吹料盘(避免局部过热变形)。
    4. 烘干时注意避开强气流直吹线盘侧面。
    5. 勿将料盘直接搁在网状架子上(建议垫底金属板等平整受热面)。
    6. 取出高温料盘时注意烫伤。
    7. 注意防火与用电安全。
    8. 尽量选用箱内温度均匀的设备;避免使用家用微波炉等加热严重不均的方式;更推荐恒温鼓风干燥箱类设备。

    (可插入「变形 vs 正常」料盘对比照片,注意控制烘干温度与摆放方式。)

    干燥受潮对比

    耗材受潮的影响

    未受潮受潮
    表面相对整洁、颜色正常、力学性能在规格内可能出现痘痕/毛刺/拉丝、颜色发白、力学性能下降等(因材料而异)

    (可插入 RH80% 环境下拆封后第 1 / 2 / 3 天打印同一模型的对比图。)

    * 上述吸湿对比示例可能因产品系列而异(例如 PAHT-CF),请在插入图片时于脚注中注明材料系列。

    留言咨询

    提交