Synced from Product Parameters V2: Basic & Appearance
| >ASA-Aero LT-effect of printing Температур on foaming < / td > < / tr > < tr > < th > Recommended printing conditions < / th > < td > Nozzle Temperature240-280 ° CRecommended Nozzle Diameter ≥ 0,4 mmRecommended build поверхн treatmentGlass, PEI Film or PC FilmBuild тарелк temperature80-110 ° CChamber TempSealing or 40-70 ° CCooling fan speed0-50% Print может speed30-90 мм/sRetraction distanceoffRetraction speedoffRecommended Поддержк MaterialN/ADrying setting60 ℃ for 4-5hAnnealingN/A < / td > < / tr > < / tbody > < / table > < h3 > Printing Tips < / h3 > < p > Printing Tips: 1. Из-за того, что вы сказали, что у вас проблемы, Это как раз то, что нужно Сотвори из этого проблему. Это как-то связано с тем, что у меня нет выбора. А тож неясн температур (40-70 ° C) is required printing дюринг to release the внутрен классифициру of the printed parts И когда это случится, Это как раз то, что нам нужно Пожалуйста, приглашение.3.
Пока нет совпадений по профилю.
ПАРАМЕТРЫ ПРОДУКТА V2
Параметр печатиПараметры продукции, которые синхронизированы и взаимосвязаны между собой, могут использоваться в качестве отправной точки для разрезания и тестирования женьшеня. Printing WindowCore temperature, speed and cooling settings from Product Parameters V2.
Nozzle Temperature
240 - 280 °C
Bed Temperature
80 - 110 °C
Print Speed
30 - 90 mm/s
Suggested Nozzle
0.4 - 0.4 mm
Cooling Fan
50 %
Hardware & PlatformNozzle, build plate and pre-print preparation recommendations.
Build Plate Material
PEI Film or Coating with PVP glue
Support & CompatibilitySupport material, spacing and compatible material recommendations.
Raft Gap
0.18 - 0.2 mm
Прикладные дела, которые совпадают с текущими потребностями
Отображаю конкретные классификации в реальном времени в разделе приложений за кулисами
1 Дело.
Общие вопросы, не включённые в данный момент, пожалуйста, ожидайте. 通用安全提示（FusRock）
耗材（防潮）储存要求
耗材受潮处理方案及方法
烘干参数 PTC 小型烘干盒：60–70℃，烘干 4–6 小时。 小型恒温鼓风烘干机：箱内温度场往往不均匀，可能导致料盘变形；此类设备上建议适当降低温度并缩短单次烘干时间（示例：40–45℃，约 4 小时），并结合材料详情中的干燥建议综合判断。 重要：若按此温度烘干后打印效果仍无改善，请先用空料盘做温度测试，再酌情提高烘干温度，以防温度过高或不均匀导致料盘烘干变形。 大型恒温鼓风烘干机：60–70℃，烘干 4–6 小时。 PS：为什么不同烘干设备适用温度会有差别？可在后台插入说明或外链「点击了解」。 注意事项 ⚠ 操作前请阅读
（可插入「变形 vs 正常」料盘对比照片，注意控制烘干温度与摆放方式。） 干燥受潮对比 耗材受潮的影响
（可插入 RH80% 环境下拆封后第 1 / 2 / 3 天打印同一模型的对比图。） * 上述吸湿对比示例可能因产品系列而异（例如 PAHT-CF），请在插入图片时于脚注中注明材料系列。 Прикладной отказ от ответственности, пока не показанный. Пожалуйста, сначала выберите или сопоставите записи «параметров связанных продуктов V2» для продукта за кулисами. Copyright & Terms of Use Notice
Thank you for visiting our website! Please carefully read the following Copyright Statement and Terms of Use before using this website: Copyright Statement All content on this website, including but not limited to texts, images, graphics, audios, videos, software, as well as their compilations, codes and technical architectures (collectively referred to as the "Content"), are owned by this website or relevant right holders and protected by the Copyright Law of the People's Republic of China and other applicable laws and regulations. Without the prior written authorization of this website, no entity or individual may copy, repost, disseminate, modify, display, adapt, mirror, upload, download or otherwise use the Content of this website in any form. The copyright of any third-party content quoted on this website shall belong to the original right holders. If your legitimate rights and interests are infringed due to reasons not attributable to this website, please contact us promptly, and we will handle the matter immediately upon verification. Terms of Use You may browse, download or print the Content of this website for non-commercial purposes in compliance with relevant laws, regulations and this Notice, provided that all copyright notices and other proprietary information are retained without any modification whatsoever. Any commercial use of the Content or services of this website is strictly prohibited, including but not limited to creating derivative works based on the Content, selling or distributing the Content to third parties. It is prohibited to use automated tools (such as crawlers, robots, etc.) to obtain, copy, monitor or attempt to access the content or data of this website. Disclaimer This website endeavors to provide accurate and reliable information, but makes no express or implied warranties regarding the completeness, timeliness or accuracy of the Content. This website shall not be held legally liable for any direct or indirect losses arising from your use of the Content or services of this website. This website may contain links to third-party websites, and this website assumes no responsibility for the content and acts of any third-party websites. Rights Protection If you violate this Notice and infringe upon the legitimate rights and interests of this website, we reserve the right to pursue legal liabilities, including but not limited to filing a lawsuit or taking other legal measures. Should you have any inquiries regarding this Notice, please contact us via: [email protected] The final right of interpretation of this Notice belongs exclusively to this website.  
|
