Synced from Product Parameters V2: Basic & Appearance
| recommended printingconditions | nozzle temperature250-270 ° crecommended nozzle diameter0.4-1.0 mmrecommended build surfacepvp gluebuild plate temperature100-110° cchamber tempsealing or 40-70° ccooling fanprint speed30-120 mm/sretraction distance1-3 mmretraction speed1800-3600 mm/minrecommended supportmaterialfusfree ™ s-멀티 quick-remove supportdrying setting70℃ for4~6 hannealingn/a |
|---|
| nozzle temperature250-270 ° crecommended nozzle diameter0.4-1.0 mmrecommendedbuild surface treatmentpei 또는 coating with pvp gluebuild plate temperature100-110° cchamber tempsealing 또는 40-70° ccoolingprint speed30-120 mm/sretraction distance1-3 mmretraction speed1800-3600 mm/minrecommended supportmaterialfusfree ™ s-멀티 quick-remove supportdrying setting70℃ for4-6 hannealingn/a |
printing tips:fuscoating ™ nexabs-gf25 has a higher fiber content compared with ordinary abs-gf.이 기술은 더 improves thewarping resistance and rigidity of abs materials챔버 temperature can properly reduced to achieve energy saving. if the filament has been opened for a longtime and problems such as air bubbles and stringing appear during the printing process.70° c에서 4-6 hours로 filament를 dry 주십시오. 이것은 좋은 환경에 의하여 프린터 자리를 변경한 것입니다fuscoating ™ nexabs gf25 can maintain a core skin structure from the에서 extrudedmelt polymer is ina laminar state when it flows stably based the mechanism, that the melt polymer is ina laminar state.그러나,when the printing speed is too high, the melt flow state will become unstable,the filaments extruded from the nozzle will no longer have the skin-core structure anymore.when이 phenomenon occurs, which can the rough surface of the printed part.프린팅 temperature increase 또는 extrusion speed reduce. 파투스 (phaetus)를 recommended to use"hardened steel nozzles or nozzles with greater abrasion resistance,which can effectively i"
No matching print profile files.
연결된 제품 파라미터 V2의 값으로, 슬라이싱 및 시험 인쇄의 출발점이 됩니다.
Core temperature, speed and cooling settings from Product Parameters V2.
Nozzle, build plate and pre-print preparation recommendations.
Support material, spacing and compatible material recommendations.
No solution entries for this product yet.
No FAQs for this product yet.
通用安全提示（FusRock）
| 短期不使用时 | 放入密封防潮盒或进行简易抽真空即可，避免阳光直射。 |
|---|---|
| 长期不使用 | 将耗材放入出厂铝箔袋并尽量排出袋内空气（条件允许时在袋内再放一包干燥干燥剂）；外套一层家用抽真空保鲜袋后抽真空。置于阴凉干燥处，避免阳光直射。 |
PTC 小型烘干盒：60–70℃，烘干 4–6 小时。
小型恒温鼓风烘干机：箱内温度场往往不均匀，可能导致料盘变形；此类设备上建议适当降低温度并缩短单次烘干时间（示例：40–45℃，约 4 小时），并结合材料详情中的干燥建议综合判断。
重要：若按此温度烘干后打印效果仍无改善，请先用空料盘做温度测试，再酌情提高烘干温度，以防温度过高或不均匀导致料盘烘干变形。
大型恒温鼓风烘干机：60–70℃，烘干 4–6 小时。
PS：为什么不同烘干设备适用温度会有差别？可在后台插入说明或外链「点击了解」。
⚠ 操作前请阅读
（可插入「变形 vs 正常」料盘对比照片，注意控制烘干温度与摆放方式。）
耗材受潮的影响
| 未受潮 | 受潮 |
|---|---|
| 表面相对整洁、颜色正常、力学性能在规格内 | 可能出现痘痕/毛刺/拉丝、颜色发白、力学性能下降等（因材料而异） |
（可插入 RH80% 环境下拆封后第 1 / 2 / 3 天打印同一模型的对比图。）
* 上述吸湿对比示例可能因产品系列而异（例如 PAHT-CF），请在插入图片时于脚注中注明材料系列。
