FusForce™ PAHT is specially developed for FDM 3D printing process, and its substrate material is high temperature nylon, which has low density, low moisture absorption, high strength, high abrasion resistance, excellent chemical resistance and high heat resistance. It also has good dimensional stability, no warpage and no shrinkage during the printing process, and can be used with FusFree™ S-PAHT Quick-Remove Support material to solve the problem of poor molding effect on the support surface of complex models.
Product highlights
Low Mositure Sensitivity
FusForce™ PAHT based on modified high temperature nylon, whose saturated moisture absorption rate is only one fifth of ordinary PA6, completely solving the defects of the mechanical properties and dimensional stability of nylon materials that change greatly after absorbed moisture.
Super Abrasive Resistance
FusForce™ PAHT has a low coefficient of friction, self-lubricating properties and excellent wear resistance, which can easily meet all kinds of high-strength gears or industrial applications with high wear requirements.
Product introduction
FusForce™ PAHT is specially developed for FDM 3D printing process, and its substrate material is high temperature nylon, which has low density, low moisture absorption, high strength, high abrasion resistance, excellent chemical resistance and high heat resistance. It also has good dimensional stability, no warpage and no shrinkage during the printing process, and can be used with FusFree™ S-PAHT Quick-Remove Support material to solve the problem of poor molding effect on the support surface of complex models.
Product details
| Parameter | Value / range |
|---|---|
| Color | Natrual, Black |
| Filament Ø | 1.75 mm |
| Net weight | 1 kg |
Material properties
Physical properties
| Property | Test method | Typical value |
|---|---|---|
| Density | ISO 1183 | 1.21 g/cm³ |
| Water absorption | ISO 62: Method 1 | 2.59 % |
| Melting temperature | ISO 11357 | 231 °C |
| Melt index | - | 280 g/10min |
Thermal properties
| Property | Test method | Unit | Dry Condition | Saturation hygroscopic conditions | Annealed + moisture conditioning |
|---|---|---|---|---|---|
| HDT A | ISO 75: Method A (1.80 MPa) | °C | 72.5 | 48 | - |
| HDT B | ISO 75: Method B (0.45 MPa) | °C | 79.6 | 60.0 | - |
Mechanical properties
| Property | Test method | Unit | Dry Condition | Saturation hygroscopic conditions | Annealed + moisture conditioning |
|---|---|---|---|---|---|
| Tensile Strength XY | ISO527 | MPa | 69.29 ± 1.17 | 57.63 ± 2.14 | - |
| Tensile Modulus XY | ISO527 | MPa | 3329.72 ± 235.60 | 2896.78 ± 152.93 | - |
| Elongation at Break XY | ISO527 | % | 9.77 ± 1.68 | 50 | - |
| Flexural Strength XY | ISO178 | MPa | 112.64 ± 1.60 | 82.23 ± 7.36 | - |
| Flexural Modulus XY | ISO178 | MPa | 3202.24 ± 115.78 | 2408.32 ± 274.58 | - |
| Notched Impact XY | ISO179 | kJ/m² | 9.74 ± 0.84 | 13.10 ± 1.70 | - |
| Tensile Strength Z | ISO527 | MPa | - | 0.6 | - |
Printed specimen parameters:Specimens printed under the following conditions: Nozzle temp 280°C, Bed temp 80°C, Print speed 45mm/s, Infill 100%, Infill angle ±45°
Disclaimer
—
